Problem with add M6720 to V7200
Posted: Mon Dec 08, 2014 12:21 am
Dear All
I have a problem with adding a new shelf M6720 to 3Par v7200. My steps are
1. i connected v7200 DP1 to M6720 DP1 on both controller. The shelf firmware version shown unknown so i use command "upgradecage cage1" After command completed successfully
2. showcage -d cage0 no defail information available cage1 status is fine
3. there are some error said upgradepd failed in Event
4. i called and open case with HP Thailand, they the problem come from my incorrect cabling.
5. i reconnect cabling DP2 to DP1 but the problem is still presisted.
6. in 3par managaement console, there is no controller in controller menu
but all volume are accesible fine. what i want to do next is disconnect cage1 and reboot cage0
or do you guys have any workaround solution? thank you in advance.
my showcage -d shown below.
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model Side
0 cage0 --- 1 --- 1 0 0-0 - - DCN1 n/a
1 cage1 1:0:2 0 0:0:2 0 6 0-0 320c 320c DCS1 n/a
-----------Cage detail info for cage0 ---------
Position: ---
No detailed information available
-----------Cage detail info for cage1 ---------
Position: ---
Interface Board Info Card0 Card1
Firmware_status Current Current
Product_Rev 320c 320c
State(self,partner) OK,OK OK,OK
VendorId,ProductId HP,DCS1 HP,DCS1
Master_CPU Yes No
SAS_Addr 50050CC117ECAD3E 50050CC117EBFFFE
Link_Speed(DP1,DP2) 6.0Gbps,Unknown 6.0Gbps,Unknown
PS PSState ACState DCState Fan State Fan0_Speed Fan1_Speed
ps0 OK OK OK OK HiSpeed HiSpeed
ps1 OK OK OK OK HiSpeed HiSpeed
-------------Drive Info-------------- --PortA-- --PortB--
Drive DeviceName State Temp(C) LoopState LoopState
0:0 5000cca028b0220f Normal N/A OK OK
4:0 5000cca028b0250f Normal N/A OK OK
8:0 5000cca028b0070b Normal N/A OK OK
12:0 5000cca028b006f3 Normal N/A OK OK
16:0 5000cca028b00b6b Normal N/A OK OK
20:0 5000cca028b0064b Normal N/A OK OK
I have a problem with adding a new shelf M6720 to 3Par v7200. My steps are
1. i connected v7200 DP1 to M6720 DP1 on both controller. The shelf firmware version shown unknown so i use command "upgradecage cage1" After command completed successfully
2. showcage -d cage0 no defail information available cage1 status is fine
3. there are some error said upgradepd failed in Event
4. i called and open case with HP Thailand, they the problem come from my incorrect cabling.
5. i reconnect cabling DP2 to DP1 but the problem is still presisted.
6. in 3par managaement console, there is no controller in controller menu
but all volume are accesible fine. what i want to do next is disconnect cage1 and reboot cage0
or do you guys have any workaround solution? thank you in advance.
my showcage -d shown below.
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model Side
0 cage0 --- 1 --- 1 0 0-0 - - DCN1 n/a
1 cage1 1:0:2 0 0:0:2 0 6 0-0 320c 320c DCS1 n/a
-----------Cage detail info for cage0 ---------
Position: ---
No detailed information available
-----------Cage detail info for cage1 ---------
Position: ---
Interface Board Info Card0 Card1
Firmware_status Current Current
Product_Rev 320c 320c
State(self,partner) OK,OK OK,OK
VendorId,ProductId HP,DCS1 HP,DCS1
Master_CPU Yes No
SAS_Addr 50050CC117ECAD3E 50050CC117EBFFFE
Link_Speed(DP1,DP2) 6.0Gbps,Unknown 6.0Gbps,Unknown
PS PSState ACState DCState Fan State Fan0_Speed Fan1_Speed
ps0 OK OK OK OK HiSpeed HiSpeed
ps1 OK OK OK OK HiSpeed HiSpeed
-------------Drive Info-------------- --PortA-- --PortB--
Drive DeviceName State Temp(C) LoopState LoopState
0:0 5000cca028b0220f Normal N/A OK OK
4:0 5000cca028b0250f Normal N/A OK OK
8:0 5000cca028b0070b Normal N/A OK OK
12:0 5000cca028b006f3 Normal N/A OK OK
16:0 5000cca028b00b6b Normal N/A OK OK
20:0 5000cca028b0064b Normal N/A OK OK