HPE Storage Users Group

A Storage Administrator Community




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Anybody has experience replacing slot blades on Brocade DCX?
PostPosted: Fri Oct 15, 2021 11:50 am 

Joined: Thu Apr 28, 2016 1:29 pm
Posts: 25
I thought since we all are Storage guys here, I could ask this.

I am going to replace blades on a production switch DCX 8510-8

According to any document, it is pretty straightforward. Disable blade, disconnect fiber cables, remove the blade, install the new blade, reconnect cables, enable blade...

I wonder if any tips and tricks I need to know if anyone here did it before.


Top
 Profile  
Reply with quote  
 Post subject: Re: Anybody has experience replacing slot blades on Brocade
PostPosted: Sat Oct 16, 2021 12:15 am 
Site Admin
User avatar

Joined: Tue Aug 18, 2009 10:35 pm
Posts: 1301
Location: Dallas, Texas
That causes a little anxiety no matter how many times you do it.

I have 48 wooden clothes pins, that I numbered with a sharpie from 1 to 48 that I use for projects like this. Its quicker and easier to "label" the cables with a clothes pin, than to audit labels that may already be on the cables. I have an old SAS cable that I use to store the clothes pins when not in use, it is just the right length and girth for clipping the clothes pins onto. A piece of rope with knots at both ends works too.

When I replaced 16g switches with 32g switches... I hard coded the ports to run at the old negotiated speeds so as to isolate what was changing the night I swapped the hardware. We later came back to start changing hosts back to speed=auto. When you remove 1 bottleneck, the bottleneck moves somewhere else, so we wanted to separate the 2 events for easier troubleshooting/causation.

_________________
Richard Siemers
The views and opinions expressed are my own and do not necessarily reflect those of my employer.


Top
 Profile  
Reply with quote  
 Post subject: Re: Anybody has experience replacing slot blades on Brocade
PostPosted: Mon Oct 18, 2021 3:02 am 

Joined: Wed Nov 09, 2011 12:01 pm
Posts: 385
Nice tips Richard! ;)

With the DCX blades the main thing after disabling/unplugging is that one of the ejection arms actually releases the power switch on the blade, turning it off before you start pulling it out. We have the 4 slot ones so the blades are horizontal but the blades are vertical on the 8 slot. There should be a little green power led next to the ejection arm that does the power, it best to release this arm first so power is off before you wiggle things and to lock this arm last once the inserted blade is secure in place (to avoid power while some pins aren't 100%).
I suspect it'll be at the top of the blade on the 8 slots, might be tricky to evenly pull/push the blade in as it's vertical but I imagine you'll have less dangling cables in the way then with the horizontal 4 blade units. :)
Just make sure the card is in the runner slots at both the top and bottom before pushing in, take a look at both ends when pulling the old card out to get an idea of how it fits. Make sure pressure is evenly applied on both arms and as mentioned once all the way in lock the powering arm last.
I have had occasion when the blade didn't power up, give it a minute and check the lights and diagnostics to see if it's recognised. If it isn't then you may have to try again, release the powering arm first then the other and slide out a couple of inches, check alignment and go again. Might need a firm but gentle push to get all the connections in okay. The arms act as levers to help even the pressure during the pin connection part.

Oh and make sure to remove the pin covers on the new blade before inserting, nearly missed that once. :roll:


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 


Who is online

Users browsing this forum: No registered users and 24 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group | DVGFX2 by: Matt